DC8040 - DAVIES CRAIG ELECTRIC WATER PUMP ALLOY 115 LITRES WITH FITTING KIT 12V

EWP^®115 Alloy Kit Remote Electric Water Pump (12V) (PART #8040)

The EWP^®115 Alloy12V is available for purchase in following options:

• Pump Only (Part #8140) 
• Kit (Part #8040)
• Combo with Controller (Part #8950)

The EWP^®115 (115 litres per minute) pump is suitable for small, medium, large, high- performance and 4WD vehicles. It’s a performance product that improves engine cooling control and capacity whilst giving you more power and torque and improved fuel economy.

The EWP^®115 is a practical alternative to the mechanical belt-driven pump or fitted as an auxiliary pump. Mechanical belt-driven water pumps run directly off the motor and sap engine power… the EWP^®115 is hardwired into your electrical system, by-passing the engine and releasing up to an additional 10kw (13hp).Our EWP range are also extensively used inIntercooler Applications.

EWP& CONTROLLER INSTALLATION DEMONSTRATION

Combined with an LCD EWP^®/Fan Digital Controller (Sold separately Part#8002 or EWP^®Combo Pack) will manage both the EWP^® and Thermatic^® fan operation. The Digital Controller will vary the speed of the EWP^® in response to the engine’s coolant temperature. Multiple temperature settings are provided on the Controller for either maximum power or fuel efficiency. The Thermatic^® Fan/s will be activated automatically once the engine coolant rises 3°C (5.4°F) above the targeted (set) temperature. The Digital Controller will automatically run on for three minutes (or to 10°C/ 14°F below the set temperature) after engine shut down, eliminating‘heat soak’ and extending engine life. The EWP^®Controller Combo Pack is supplied in a do-it-yourself kit with everything you need for fitment to your vehicle’s engine, including an easy-to-follow DIY instruction booklet.

The world’s most advanced total engine cooling management system:

 universal fit

 more power

 more cooling

 increase fuel efficiency

 extend engine life

 world-leading technology

EWP^®INSTALLATION OPTIONS

Installing an EWP^®as an AUXILIARY PUMP

• Leaving the mechanical water pump in place, install the EWP^® into the bottom radiator hose.
• Remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation when the thermostat is closed. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

EWP^® INSTALLATION– disabling Mechanical water pump

• Leaving the mechanical water pump in place, install the EWP^® into the bottom radiator hose and remove the manufacturer’s thermostat.
• You will need to bypass the water pump pulley by installing an appropriate length belt (not supplied). This method makes for an easy installation.
• If running the pump continuously remove the thermostat and drill two approx. 3mm (1/8") holes in the thermostat plate to allow some coolant circulation. Re-install ensuring that the thermostat housing is clean and a new gasket is used if required.

In both these cases, the EWP^® will pump past the impeller of the mechanical water pump.

Disengaged mechanical water pump (recommended)

• Remove the mechanical water pump and remove the thermostat.
• Then remove the impeller from the mechanical pump shaft. Retain the mechanical water pump using the pump pulley as an idler to avoid re-routing the drive belt.

• Block any bypass passages and re-install the disengaged water pump ensuring that all gasket surfaces are clean and the new gaskets are properly fitted to prevent leaks.
• Install the EWP^Ò into the bottom radiator hose.

Removed mechanical water pump (Ideal)

• Remove the mechanical water pump and thermostat from the engine.
• Install a Davies Craig EWP^® Header Adaptor or blanking plate (not supplied). Ensuring the gasket surfaces are clean and the appropriate gasket or sealant is used to prevent leaks.
• Install the EWP^® into the bottom radiator hose. This method will require you to modify or replace the standard radiator hose.
• Install an appropriate length belt (not supplied) to drive the accessories.

In most cases EWP^® will be adequately supported by the radiator hose. Where mounting is required, the EWP^® must be soft mounted to protect against vibration. For the EWP^®115, EWP^®140 and EWP^®150 Part #8700 or #8710 Mounting bracket is recommended.